Questions & Answers

2015 crosstrek program OEM RF transmitter lo enable 3x start.

0 votes

 

2015 CROOSTREK WONT REMOTE START. HOW DO I PROGRAM OEM RF TRANSMITTERS TO REMOTLY START VEHICLE.

I FOUND THIS TROUBLESHOTING THE EVO-ONE. 

DECRYPTOR DONE AND UPDATED , INSTALLED BACK TO CAR BUT DOESNT REMOTE START WITH 3X LOCK)

If the red led is not turning on then the module is not receiving a start command. Verify that the RF kit being used was properly programmed.

If it does turn on briefly then shut off right away, pay attention to the parking light flashes. 

asked Dec 6, 2016 in Subaru by felipe sesnich (160 points)

2 Answers

0 votes
Did you enable D2 option on bypass?
answered Dec 6, 2016 by Edrice Iraola (1,090 points)
where exactly do i enable D2 option ?

 

how do i program oem key fob to remote start ?
0 votes
Please provide the service number of the actual Evo unit and not the Flashlink Updater-2 module. Is your vehicle a Push to Start or Regular Key vehicle?

 

Thank you,
answered Dec 6, 2016 by Jesus Monroy (63,860 points)
serv No. 002B02 139965.   ,is a regular key vehicle .

thanks for you help
http://fortin.ca/en/support/002b02139965/ You currently have remote starter firmware in the bypass.

- I would suggest first flashing the newest firmware to the bypass (79.39)

- followed by a master reset : http://wirecolor.com/en/qa/50193/faq-how-do-i-reset-my-evo-all?show=50193#q50193

- Followed by reprogramming it in the vehicle from start to finish including DCryptor.

- Next, I would flash the remote starter to the newest firmware version (1.21)

-Perform a master reset of the remote starter as well: http://wirecolor.com/en/qa/67178/evo-one-reset?show=67178#q67178

- Followed by enabling all necessary options in both the bypass and remote starter.

 

Once you have corrected these errors then re-test the module in the vehicle.
ser No:  002B07 139965

I did the decrypt again from the beginning and upgrade , flash both the remote starter 1.21and the bypass 79.39. enable 38.4 option and still

the vehicle doesn't remote start . the blue led doesn't flash when lock or unlock .when i try to remote start by 3x lock , the parking lights flash 3 times . how do I program the oem remotes to the unit .
I had the same issue with my 15 Crosstrek. Crutchfield had me go back to firmware version 1.19 and reprogram and it works now.
you need to enable 38.2 not 38.4
Derek, while my starter is working, I cannot shut the car off with the remote. I am supposed to be able to press lock 3X to shut it down (when it has been started remotely), but it does nothing. So if I start it remotely and then decide that I am not ready to leave, etc., I have to let ir run 15 minutes or go out and manually stop it. How can this be addressed? Thanks!
When you press lock on the oem remote does the blue led on the module flash? If so how many times does it flash when pressing lock?
sorry it's 38.2 function already enabled.

still doesn't remote start . when regular key is lock 3x to remotely start nothing happens . blue led doesn't flash at all.

only parking lights flash 3times after trying to remote starting by 3x lock with OEM key key fob remote

How do i get the oem remote ready mode to remote start car
did you had a 15 croostrek, with regular key .

how did you make work , how did you downgrade the firmware?
3 flash means ready mode not enabled. Cut the yellow loop on the evo f your vehicle is automatic transmission
Derek, when the car has been started remotely, the red and yellow lights are solid. When I press the Lock button on the factory remote, nothing happens (red and yellow continue to burn).
Felipe, in order to get it to start my 15 Crosstrek (regular key), I had to do the following:

1) In the software, toggle to Remote-Starter, and plug in the brain to the FLU.

2) Click on "Evo-One Updates"

3) In the firmware options, scroll to 1.19 and click select or "Recommended Update". Then click "Flash Update" at the bottom.

That should update the brain to the 1.19 firmware. From there, you set the options as they've been recommended.
...