Questions & Answers

Evo one, After remote start, Can't turn the keyless switch to ON position

0 votes
After remote start, I Cant turn the keyless switch to ON position. It seems the fastkey is not being trggered, I have to turn off the engine by steping on the brake padel for example. then start the engine normally to drive. My car is 2015 evolution MR (FastKey)

How to drive after remote start without having to start the engine again.
closed with the note: connection issue. Solved by connecting to correct wire.
asked Mar 13, 2021 in Mitsubishi by nhelal56@hotmail.com (180 points)
closed Mar 24, 2021 by derek g

2 Answers

0 votes
did you cut the TUMBLER SENSE wire and connect to the evo one red connector ?
answered Mar 14, 2021 by Haidar Jabbar (22,390 points)
Yes I did. I cut the wire pin#10 from the car black plug at left side of the steering wheel and link one side to the white/red wire other to white/green from the red connector, the white/green is T connected to Red/Blue A9 from the (A) white connecter. I have not connected the Motion detector wire as I did not find the plug (could be not applicable or location is not same as the older model of lancer since Fortin manual created based on older models)
0 votes
Any one? I sent to Fortin support but seems no one is checking the masages.
answered Mar 22, 2021 by nhelal56@hotmail.com (180 points)
If youd like to contact support please send email to support@fortin.ca.

I checked the system and no email or support ticket has been received from your e-mail as of yet.

 

I can look into your issue, I will need the S/N to the module please.

How to get the S/N? Is it written in the box? the unit alreay installed somewhere under the steering wheel term. There is a code stamped on the box with number ( 002B04 159310)

Can you please also provide a picture of the intterupt you have done to the tumbler sense wire.

 

This should be the guide you followed: https://fortin.ca/download/24841/evo-one_ig_reg_bi_mit_lancer_evolution_key_d_24841.pdf

When you end unlock from the remote AFTER the vehicle is remote started, does the blue led on the evo blink twice?

 

Please also select the correct vehicle and load that into the evo. You selected a standard key, your vehicle from what you wrote above is a fast key.

https://fortin.ca/en/vehicles/mitsubishi/lancer/2015-fast-keyless/

Thanks for notes. The wiring must be same as the guide mentioned. From the back of the tumbler plug I cut the 3rd wire from the lower/right of the plug. I will take a photo once I removed the term to reload the vehicle to the Evo one (I remember that there is only one choice (Standard key) but let me try again and let you know.

The unit blink blue twice once I unlock the door after remote start. 

Below (attached a photo of the connected wire).

Once I load Lancer Evolution, There is no option to change from standard key, do you mean should I chose reguler lancer instead of Evolution? 

At the alarm system choice, which one should I use to keep the oem alarm system as it is?

Regards,

 

image

 

Yes, seelct lancer fast key instead and be sure to load suggested options.

You would answer no alarm.

 

I can't see much in the picture, but i do see quick connects. Alot of times t-taps or crimp connectors can be the source of your problem.

 

a test to try: remote start the vehicle, send unlock, then manually unplug the red connector on the evo and see if you can turn they tumbler.
I will,

Do I have to do Dcryptor again after loading the vehicle?
it would be a good idea to re program it once you load the version and suggested options.

 

You could even do a master reset before any of that to start with a clean slate: https://fortin.ca/en/download/61931/61931.pdf
*for evo one hold button and plug in main 6 pin connector.

I did all that, Same issue.

Once I did (a test to try: remote start the vehicle, send unlock, then manually unplug the red connector on the evo and see if you can turn they tumbler.)

Dash Keyless light was ON. Also Once I disconnect the red connector as a test, I could not turn the key to ON position while the car was Off.

It is obviusly that tumbler key signal is OK since the car starting normally without remote start although the signal wire is cut to connect to the EVO unit.

Pls let me know if you have any other suggestions to fix the issue.

Please send clear pictures of the connections youve made to the tumlber so we can verify the connector location and pin placement. support@fortin.ca

 

My understanding is that the wire is opened at take over to allow the tumbler to turn, if it is not turning when you unplug the connector it seems as though it might be the wrong wire or a connection issue itself. 

Client was on the wrong tumbler sense wire.

 

On the 2015 lancer evolution fast key, it is the green wire at the tumbler connector, Pin 2.

 

Client was on a red/green wire in pin 8.
...