G37 STAY LOCK AFTER REMOTE START

Question

AFTER REMOTE START THE ENGINE THE DOORS WILL NOT UNLOCK BY THE KEY

I PROGRAMMED THE MODULE SEVERAL TIMES BUT NOTHING CHANGE

WHAT DO I NEED TO DO?

Answer 1

Hello,

What is the S/N number on the back of the module?

Are you referring to the OEM remote not working once the vehicle is remote started?

Best regards.

Comments

HI,

yes, the key is OEM, after remote start the engine the doors are lock and could not open them by the remote.

s/n:

001A07 563905

---

Hello,

Turn off A14, B1, B2, B3 then click save options and re test.

When the vehicle is remote started and you press unlock what do the led's on the evo do?

Best regards.

---

THANKS FOR YOUR SUPORT.

I FORGOT TO TELL BUT THE A15 PINK/BALCK WIRE WHO NEEDS TO ATTACHED THE TCM, I CONNECTED IT TO THE DRIVER DOOR PIN.

I DID IT BECAUSE WHEN I CONNCETED IT TO THE TCM THE CAR DID NOT STARTED BY THE REMOTE AND WHEN I CHANCHED IT TO THE DRIVER PIN WIRE IT STARTED BY THE REMOTE/

ALL THE OTHER WIRES AND T HARNESS CONNECTED BY THE BOOK.

I WILL TRY WHAT YOU SAID

---

DO YOU MEAN IF I START THE CAR NOT BY THE REMOTE? DIDNT TRY THE REMOTE WHILE ENGINE STARTED NORMALLY

---

Does the OEM remote work while the engine is started normally?

---

I TURNNED OFF THE OPTIONS BUT STILL STAY LOCK

---

does the oem remote work while the engine is started normally?

thank you.

---

I don’t understand what you mean.

If I start the car by the push button regularly, I cannot use the key to lock and unlock

---

That is why it does not work when remote started either. The remote starter starts the car the same way a person does, so it makes sense the remote does not work.

You will need rf kit to control door locks when remote started.

Best regards.

---

Can I by pass the option without the kit you mentioned?

If not can you give me link for that?

---

There is no bypassing this since the vehicle does when started normally.

Here are compatible rf kits: https://fortin.ca/en/technologies/compatible-remote-controllers/

Please note a flash link updater may be required to enable proper rf kit protocols in the evo-all.

---

thank you very much for your help.

i dont know which one to order, i have the NIS1 kit so i want just the parts that needs to complete the kit.

if you can help me with that.

---

Any Fortin rf kit listed in the link above can work with the evo-nist1.

Just be sure to check with your point of purhcase that the kit you order includes the RFA-2A adapter.

Best regards.

---

In the including kit there is nothing about RFA-2A adapter just antena cable.

there is somthing that i missing?

---

If the kit you purcahse does not include the adapter you would need to purchase it seperatly.

---

do you have link?

appreciate that

---

https://fortin.ca/en/where-to-buy/installation/

---

can you tell me please,

my OEM key is smart key and i can enter the car and open the trunck while pushing bottom on the door if my OEM key near by.

Are the kit use as smart key as well without the OEM one?

---

No the after market rf kit will not work that way. You must always carry the OEM remote with you when using the vehicle.

---

It will not turn on without the OEM key near by?

---

You must always carry the OEM remote with you when using the vehicle.

---

Ok, thank you

---

Hi, i bought the rf411 kit and try to instell it by the guide, i start the car with OEM key by 3x close and the engine starting and the doors locks after that i tried to open the car with rf remote and the car does not open, when i clicked 2 times on the rf remote the engine shout dwon.

please help me

---

You need to connect the lock and unlock wires

https://cdn02.fortin.ca/download/102561/EVO-ALL_IG_RTS_BI_NIS1_Q60_2014_PTS_B_102561.pdf

---

Hi,

I already did that all the required wires are attached.

When I tried to program to module and keys the leds need to flash one time in the module when the program are good, but they don’t flash they stay on

---

when programming the remotes to the evo make sure you are holding the button down on the remote until the blue led comes back on solid, that is when you release the button.

---

It is come blue solid but the module don’t have any flash light just 3 light solid

---

Turn on optoin H and H2 and re try the pairing process.

---

orry but still dont working, mayve another porograming method?

---

Looking at the module (001A07 563905) you stil have not turned on option H. Please turn on option H and H2 then click save options and re attempt the rf pairing process.

Best regards.

---

when i re attempt the rf kit, what the steps i need to do? just connect the connectors?

---

You need to enable options H and H2 in the evo then click save options. Then follow the in vehicle programming: https://cdn02.fortin.ca/download/69291/EVO-ALL_RF-KIT_411_QUICKINSTALLGUIDE_F_69291.pdf

Best regards.

---

DID IT, I HAVE CHECKED ALL THE WIRES AND THEM GOOD.

STILL DONT WORKING.

---

Alright, next step is to call into the tech support line when you have the evo, rf kit, flash link and vehicle on hand so an agent can walk you through the rf pairing process and determine why it is not working.

1-877-336-7797

Mon - Fri

8 am 6 pm est.

Best regards